Centrifugal
Turbo-Tech Ti centrifugal air and nitrogen compressors — Turbo-Tech / Tlingte — Wuxi compressor works
Turbo-Tech Ti centrifugal air and nitrogen compressors · Turbo-Tech / Tlingte — Wuxi compressor works
Datasheet
Product overview
Power: Driver selected to duty · Pressure: 0.06–1.60 MPa(G), family envelope · Flow: 1200–24000 Nm³/h, family envelope
Turbo-Tech's current Ti centrifugal page gives 1,200–24,000 Nm³/h flow and 0.06–1.60 MPa(G) pressure as family ranges, with air and nitrogen explicitly named as media. The gauge designation is present in the source. Normal-volume reference temperature and pressure are not defined on this page; agree them before comparing capacities with an inlet-volume or ISO FAD rating. The endpoints are not a single guaranteed selection and do not identify motor power.
The manufacturer describes Ti as the replacement for earlier Til, Va and Cr ranges, with revised aerodynamic design and greater modularization and standardization. Its stated 3–6% efficiency improvement is a manufacturer comparison without a complete buyer-specific test basis here. Select by the actual required flow/pressure, inlet temperature, altitude and humidity, load profile and available cooling, then compare total package input at agreed operating points rather than assuming that percentage becomes site savings.
Request the selected model/frame, minimum stable flow and control strategy, performance curves, cooling-water duty or offered cooling arrangement, voltage/start method, noise conditions, dimensions, maintenance access and package supply boundary. For clean-air service, specify oil, particles and moisture separately and obtain current evidence for the exact model. The original Ti photograph shows a complete example package, not proof of its frame rating or inclusion of all downstream air-treatment equipment.
| Catalog reference | TLINGTE-TI |
|---|---|
| Machine | Centrifugal |
| Power | Driver selected to duty |
| Working pressure | 0.06–1.60 MPa(G), family envelope |
| Published flow | 1200–24000 Nm³/h, family envelope |
| Air quality | — |
| Duty | General industry |
| Supply | Not specified |
| Plant | Turbo-Tech / Tlingte — Wuxi compressor works |
| Series / mechanism | Ti centrifugal |
| Published media | Air and nitrogen; offered gas duty to confirm |
| Family flow envelope | 1200–24000 Nm³/h; normal reference conditions to agree |
| Family pressure envelope | 0.06–1.60 MPa(G); source explicitly gauge |
| Range interpretation | Family endpoints, not one guaranteed paired duty |
| Series history | Manufacturer describes Ti replacing Til, Va and Cr |
| Design description | Revised aerodynamics; modularized and standardized design |
| Motor / package input | Selected duty and actual driver rating to obtain |
| Selection documents | Inlet conditions, operating map, stable flow and controls |
| Package boundary | Cooling, electrical, foundations and air treatment to agree |
| Clean-air acceptance | Exact model evidence; oil, particles and moisture specified separately |
| Image | Original manufacturer Ti package photograph; exact frame not named |
Plant
Turbo-Tech / Tlingte — Wuxi compressor works
Wuxi
The plant remains the seller. This desk issues the English duty sheet so quotes are comparable across clusters.
- TLINGTE-RA · Process-duty driver selection
- TLINGTE-RECIP · Duty-selected; catalog ceiling 7350 kW
Specification pages
Specifying a Centrifugal duty
| Duty | Write on the RFQ |
|---|---|
| Compressor for wastewater treatment | Most aeration trains want low-pressure blowers. If this RFQ is actually 7–8 bar plant air for valves and instruments, say so — it is a different machine from a maglev blower. |
| Centrifugal compressor manufacturers in China | Centrifugal machines are duty-built. A 250 kW “centrifugal compressor China” RFQ without gas, suction and discharge pressure cannot be quoted. |
Same type
Related Centrifugal products
Compare the published product information for each manufacturer.
| Catalog ref. | Type | Power | Pressure | Flow | Air quality | Plant | |
|---|---|---|---|---|---|---|---|
 JTL-INDUSTRIAL-AIRJTL JE centrifugal air compressors and JED single-stage range
|
Centrifugal | JE6000: 355–800 kW · configuration range | JE: 2.2–10.5 barG · select operating point | JE6000: 80–130 m³/min · reference basis to agree | — | Jintongling | RFQ |
 HANWHA-CENTRIHanwha SM / SM100 Pro centrifugal air compressor selections
|
Centrifugal | SM2100 150–335; SM3100 Pro 250–600 kW | SM2100 5.0–11.4 bar(A); Pro duty to select | SM2100 1400–3550; Pro 3300–5690 m³/h | — | Hanwha Power Shanghai — compressor sales and service | RFQ |
 HYTP-ISOTHERMAL-AIRHangyang single-shaft isothermal main-air compressors
|
Centrifugal | Motor or steam turbine;duty-specific | Selected main-air delivery duty | ASU scale below40,000 Nm³/h;not air flow | — | Hangyang Turbine | RFQ |
 IHI-SULLAIR-TXIHI-Sullair TX centrifugal air — 4–9 barg series selection
|
Centrifugal | TX series:150–425 kW | TX series:4–9 barg | Offered model flow/reference required | — | IHI-Sullair | RFQ |
 SHAANGU-EShaangu E horizontal-split process centrifugal compressors
|
Centrifugal | Selected train driver/input to agree | Actual gas operating envelope required | Project-specific flow/map and reference | — | Shaangu | RFQ |
 KFAS-DAKFAS DA single-shaft centrifugal compressor engineering references
|
Centrifugal | 1040 kW shaft power, code 6060 | 0.097 to 0.70 MPa absolute | 210 m³/min, code 6060 | — | KFAS | RFQ |
TLINGTE-TI: Voltage and frequency matter as much as bar. State both. Include the required operating conditions with your enquiry.
Issue RFQ